Carlton 2518 Návod k obsluze Strana 169
- Strana / 199
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
8. Range of programmable parameters
Description Programmable range Default values
LOW (Minimum RPM value
permitted)
500 ÷ 2700 (*) RPM, steps 10RPM 2240
HIGH (Maximum RPM value
permitted)
2000(*) ÷ 5000 RPM, steps
10RPM
2440
BACK (reaction time for
reverse valve)
0 ÷ 2500ms, steps 10ms 300
PULSES (number of
pulses/revolution for RPM)
2.0 ÷ 200.0 pulse/rev, steps 0.1
pulse/rev
129.0
TYPE (reverse function is
ON)
ON or OFF ON
(*) LOW value shall never exceed HIGH value (and vice versa), and priority shall be
given to the LOW value with 20RPMs hysteresis; e.g: if a LOW value is programmed
equal to 1980RPM, the HIGH value shall not be lower than 2000RPM;
Now, by releasing all keys, the monitor operates under standard condition and the
initial test is carried out again.
7. Technical features
Supply voltage 10 ÷ 16 Vdc
Max. current absorption at 16 Vdc (excluding outputs) 200 mA
Protection degree IP 66
Operating temperature range -20 / +70 °C
Storage temperature range -25 / +85 °C
Mechanical vibrations resistance 2 g random
Reference standards for the project MC14982
Autofeed Settings for Carlton Chippers
Engine Make Engine Model HP Rating High Setting Low Setting CAL
Vanguard Big Block V Twin 35 HP 3200 2400 98
Kubota D1105T 33 HP 2440 2370 12
Kohler
CH740
27HP 3330 2900 97.4
Kubota V3300T 88 HP 2440 2370 12
Kubota V3800T 99HP 2440 2370 12
John Deere 99 HP 2440 2240 129
John Deere 140 HP 2440 2240 129
John Deere 6068T 173 HP 2440 2370 129
John Deere 6068H 250 HP 2440 2370 129
- Drum Style Brush Chippers 1
- CALIFORNIA 3
- Proposition 65 Warning 3
- IMPORTANT NOTICE 17
- Warranty Validation Form 19
- ® Chipper 23
- We Pride Ourselves 25
- SAFETY FIRST ALWAYS! 27
- CUTTER DRUM 29
- SAFETY: 37
- HITCH & HITCH BOLTS 39
- CUTTER DRUM DOOR HINGES 40
- DOOR PIN & PADLOCK 40
- ANVIL WORKING EDGE 41
- ® Starplex II 43
- ® monitors the 45
- ® control is 45
- ® control 45
- ® manual 45
- ENGAGED 46
- DISENGAGED 46
- CLUTCH ENGAGEMENT 46
- LIFT CYLINDERS 49
- LIFT CONTROL VALVE 49
- COVERED AIR VENT 49
- REAR JACK STAND 50
- OPTIONAL 50
- FRONT JACK STAND 50
- AIR VENT CLOSED 50
- AIR VENT OPEN 50
- CLEAN-OUT DOOR 51
- HANDLES 51
- HYDRAULIC WINCH 53
- SELECTOR VALVE SWITCH 53
- CONTROL VALVE 53
- ALWAYS WIND ROPE 54
- UNDER THE WINCH 54
- CONNECT LIGHTS 57
- LOCK PIN IN GROOVES 60
- ENGINE OPTION 61
- THROTTLE SWITCH – LOW (IDLE) 62
- THROTTLE SWITCH -HIGH 62
- FEED CONTROL - FORWARD 62
- FEED CONTROL - REVERSE 62
- AUTO-FEED® ONAUTO-FEED® OFF 63
- AND BUTT END FIRST 65
- LEVER 2 69
- LEVER 1 69
- WINCH CONTROL VALVE 70
- (IF EQUIPPED) 70
- SHUT DOWN PROCEDURES 71
- ROTATE CHUTE 72
- MAIN FILTER SAFETY FILTER 74
- RADIATOR SCREEN 74
- CLEAN FROM THIS SIDE 74
- ENGINE OIL FILTER 74
- COOLANT FILLER CAP 75
- FUEL/WATER SEPARATOR 75
- FEED CONTROL LINKAGE 76
- CHECK PIN & HOLES 79
- ® Axles supplied in this 80
- Starplex II grease 81
- LEVER STYLE 85
- FREEWHEEL 85
- COMPLAINT CAUSE CORRECTION 87
- HYDRAULICS 89
- PTO/CLUTCH 93
- CUTTER SYSTEM 100
- BELT TENSION 109
- ADJUSTMENT EYEBOLT 110
- ENGINE SLIDE BOLTS 110
- 2 AT FRONT OF ENGINE 110
- 2 AT BACK OF ENGINE 110
- BOLTS FRONT 113
- ENGINE SLIDE 113
- BOLTS REAR 113
- FEED WHEEL MOTOR 116
- WIRING DIAGRAM 121
- 18” DRUM 127
- Carlton 128
- 1J9RG0119A1167036 131
- IN (GND) B 148
- 2. Operating 149
- 6. Setting 153
- Auto-FeedReverse 155
- 0.5 sec 0.5 sec 0.5 sec 156
- 7. Technical features 157
- CAUTION 193
- Product Features 195
- WINCH INFORMATION 196
Hinkley-lighting VICTORY 4133BN manuals
Owner’s manuals and user’s guides for Lighting Hinkley-lighting VICTORY 4133BN.
We providing 1 pdf manuals Hinkley-lighting VICTORY 4133BN for download free by document types: User Manual
Komentáře k této Příručce